Galfab, Above Frame OR Hoist (AFOR Series)

The Galfab above frame hoist is designed, but not limited to CNG chassis, features outboard mounted lift cylinders and a vertical lift assist cylinder. It is designed to operate with low pressure, which will increase its life and reduce maintenance costs.

  • 10″ x 4″ x 3/8″ Main Frame Tube
  • 1/2″ x 3″ Wear Strip on Top
  • 1/2″ x 4″ Spacer Bar on the Bottom Side of the Mainframe
  • 3″ x 3″ x ¼ inch Sub-Frame
  • All Working Points Greaseable
  • 2 1/2″ Diameter Rear Hinge
  • Pintle Ready Apron
  • Auto Fold Forward DOT Bumper
  • 1″ Spring Loaded Container Locks
  • 2 1/2″ Diameter Lift Cylinder Shafts
  • 12″ Diameter Vertical Sheave and 10″ Horizontal Sheaves
  • 3/8 inch x 3 inch Winch Cylinder Rod Covers
  • 6 Inboard and Outboard Supported Outside Rollers
  • Container Long Sill Supports on Rear of Hoist Mainframe
  • 30 Gallon Oil Reservoir with Sight and Temperature Gauge
  • 25 Micron Filtration
  • Inside and Outside Controls
  • Dual Inboard 6 inch Diameter Winch Cylinders
  • Galfab Patented “Tricep” Lift Assist Cylinder
  • LED Lighting System
  • 7/8” Cable with Heavy Duty Swivel Eye Hook
  • 12″ Diameter Vertical Front Sheave
  • 12″ Diameter Horizontal Sheaves
  • 12″ Diameter Sheave Blocks
  • Suction Screen and Return Filter
  • 2-1/2″ Diameter Lift Shaft
  • Main Frame Wearstrips
  • 2-1/2″ Diameter Rear Hinge
  • All Working Points Greasable
  • 1″ Spring Loaded Container Stops
  • Front Mount Pump
  • Low Working Pressure of 2500PSI
  • Hoist Up Warning Light
  • Sealed Wiring System
  • Hoist Up Alarm
  • Backup Alarm

  • Pintle Hook Options
  • PTO
  • On Board Scale Systems
  • Work Lights
  • Rear View Camera Systems
  • Ratchet Tie Down Straps
  • Tool Boxes
  • Auxiliary Stops
  • Poly or Steel Fenders
  • Aluminum Fenders
  • Tarping Systems
  • “The Hooker” Hold on System
  • Integrated hydraulics can be used, if hydraulic tarping system is used

Model Capacity CA CA with tarp Length Dump Angle Up (sec)* Cycle times Down (sec)* On (sec)* Off (sec)* Lift Cylinder Winch Cylinder Container Length ft Apx Weight lbs
AFOR60174S069 60,000 178″ 190″ 24’4″ 50° 36 20 41 31 6″ – 4″ x 69″ DA 6″ – 3″ x 81.5″ DA 18′-22′ 7400
AFOR75174S069 75,000 178″ 190″ 24’4″ 50° 36 20 41 31 6″ – 4″ x 69″ DA 6″ – 3″ x 81.5″ DA 18′-22′ 7400
AFOR60194S069 60,000 198″ 210″ 26′ 50° 36 20 46 35 6″ – 4″ x 69″ DA 6″ – 3″ x 91.5″ DA 18′-22′ 7550
AFOR75194S069 75,000 198″ 210″ 26′ 50° 36 20 46 35 6″ – 4″ x 69″ DA 6″ – 3″ x 91.5″ DA 18′-22′ 7550

* Cycle Times are Factory developed and controlled by PTO output, oil viscosity, human and mechanical efficiency, and may vary accordingly.

CAUTION: This Equipment Should be Operated by Properly Trained Personnel. Improper Use, Misuse, or Lack of Maintenance Could Cause Injury to Persons or Property. Photos used in this brochure are illustrative only. We reserve the right to make changes at any time without notice. Information contained within this literature is believed to be the most accurate available at the time of printing.

Please contact one of the EMP Partner(s) below:
Galfab (HQ)
Call: (877) 504-1622
612 West 11th Street
Winamac, Indiana
Galfab
Call: (877) 504-1622
4020 South 15th Avenue
Phoenix, Arizona
Municipal Equipment, Inc. (HQ)
Call: (800) 248-7590
6305 Shepherdsville Road
Louisville, Kentucky
SWAT (Solid Waste Applied Technologies) (HQ)
Call: (912) 549-0005
207 Hall
Statesboro, Georgia

Recently Viewed